|
|
| |
Model/Solution Configuration |
Provider/Manufacturer |
|
Orbio ® Multi-Surface Cleaning Solution System
Orbio Multi-Surface Cleaning Solution is created using Orbio Split-Stream Technology, and available on the Orbio 5000-Sc, which utilizes water, electricity and a small amount of salt to create a sustainable cleaning solution right on-site. The system is to first vacuum with a Tennant V-LWU-13 upright vacuum with 4 passes at 1.8 ft/sec, then pre-spray with hot Orbio Multi-purpose Cleaning Solution at 1 gl/200ft2. The carpet is then agitated by a carpet rake and allowed to dwell for 10 minutes. The carpet is then extracted using hot Orbio Multi-purpose Cleaning Solution in a Tennant EX-CAN-15-HPH Carpet Extractor with Tennant High Airflow Titanium Wand using 4 wet extraction passes at a rate of 1.0 ft/sec. |
Orbio Tech, A Tennant Company Group
Minneapolis, MN
800-553-8033
Visit Website
|
|
Sears Carpet and Upholstery Care System
Sears Ultratech Truck Mount - The first step is pre-vacuum 4 passes at 1.8ft/sec. The second step is to pre-spray with Sears UltraCare Traffic Lane cleaner 6 oz/1gl at 1.0gl/200ft2 followed by agitation using a Gandigroom carpet rake. The treated sample is allowed to dwell for 15 minute prior to cleaning. The third step is to hot water extract the samples with Sears UltraCare Fiber Rinse Carpet Cleaner 32 oz/5gl metered at 2 gl/hr using 3 wet extraction passes followed by 2 dry extraction passes at a rate of 1 ft/sec on each pass. |
Sears Carpet and Upholstery Care
Lewis Center, OH
866-389-4568
Visit Website
|
|
Zerorez® Cleaning System
Zerorez® employs a patented and highly proprietary, truck-mounted green cleaning technology and system. The basic Zerorez system uses ''Empowered Water™.'' Empowered Water™ is a superior cleaning fluid that is green, non toxic, healthy and delivers a superior cleaning result without soaps, shampoos, detergents or toxic chemicals. The Zerorez® patented truck mount system applies ChemFree , at a rate of 1 gl/300 sq ft followed by rake agitation. Dwell time: 5 min. Then, using the Zerorez® patented wand system, go over the pre-treated area with 2 wet passes and 2 dry at 1ft/sec. |
Zerorez
Murray, UT
866-937-6739
Visit Website
|
|
|
| |
Model/Solution Configuration |
Provider/Manufacturer |
|
Century CEXT7
Pre-spray with Prochem Ultrapac Traffic Clean (6oz/1gl @ 1.0gl/200 sq ft) followed by agitation using carpet rake. Dwell 10 min followed by hot water extract with water only using 3 wet passes followed by 1 dry extraction pass at rate of 1.0ft/sec |
Century 400
Chandler, AZ
800-752-1777
|
|
Chem-Dry® PowerBase® 10 or PowerBase® 5 with PowerHead®
Chem-Dry® PowerBase® 10 or PowerBase® with ChemDry PowerHead®Truck Mount Pre-spray with ChemDry Traffic Lane Pre-Spray or Chem-Dry Supercharger (2cup/1gal at 1gl/200 sq ft) followed by agitation using rake. Dwell 10 min followed by hot water extract with ChemDry Natural III A & B (1pk/5gl) Carpet Cleaner and Repel Concentrate (1cup/5gl) using 2 wet passes and 1 dry at 1ft/sec. |
Chem-Dry®
Logan, UT
435-755-0099
Visit Website
|
|
|
Chem-Dry®'s CTS-Direct Drive with PowerHead®
Vacuum with Windsor VS14 upright 4 passes at 1.8ft/sec on each pass. Prespray with KB-4 Pre-Spray 16oz/1gl at 0.5gl/100ft2 (followed by agitation using rake. Dwell 10 min followed by hot water extract with ChemDry Natural IV in tank solution using the Chem-Dry PowerHead 3 wet passes at 1.0ft/sec. |
Chem-Dry®
Logan, UT
435-755-0099
Visit Website
|
|
Chem-Dry®'s Revolutionary Truck mounted system CTS-330 with PowerHead®
Pre-spray with ChemDry Traffic Lane Pre-Spray (2cup/1gal at 1gl/200 sq ft) followed by agitation using rake. Dwell 10 min followed by hot water extract with ChemDry Natural IV (1pk/5gl) Carpet Cleaner and PowerGuard Concentrate (1cup/5gl) using 2 wet passes and 1 dry at 1ft/sec. |
Chem-Dry®
Logan, UT
435-755-0099
Visit Website
|
|
Chem-Dry®'s Revolutionary Truck mounted system CTS-450 with PowerHead®
ChemDry Traffic Lane Pre-Spray or Chem-Dry Supercharger (2cup/1gal at 1gl/200 sq ft) (followed by agitation using rake. Dwell 10 min followed by hot water extract with ChemDry Natural IV (1pk/5gl) Carpet Cleaner and PowerGuard Concentrate (1cup/5gl) using 2 wet passes and 1 dry at 1ft/sec. |
Chem-Dry®
Logan, UT
435-755-0099
Visit Website
|
|
|
Chem-Dry®'s XTS Crossover Truck Mount with XTS and Truck base equipment®
Vacuum with Windsor VS14 upright 4 passes at 1.8ft/sec on each pass. Prespray with KB-4 Pre-Spray 16oz/1gl at 0.5gl/100ft2 (followed by agitation using rake. Dwell 10 min followed by hot water extract with ChemDry Natural IV in tank solution using the XTS Crossover Portable System 3 wet passes at 1.0ft/sec. |
Chem-Dry®
Logan, UT
435-755-0099
Visit Website
|
|
|
Chem-Dry®'s XTS Satellite Based Equipment with Chem-Dry Crossover Portable System
Vacuum with Windsor VS14 upright 4 passes at 1.8ft/sec on each pass. Prespray with KB-4 Pre-Spray 16oz/1gl at 0.5gl/100ft2 (followed by agitation using rake. Dwell 10 min followed by hot water extract with ChemDry Natural IV in tank solution using the XTS Crossover Portable System 3 wet passes at 1.0ft/sec. |
Chem-Dry®
Logan, UT
435-755-0099
Visit Website
|
|
|
Chem-Dry®'s XTS-Crossover with PowerHead®
Vacuum with Windsor VS14 upright 4 passes at 1.8ft/sec on each pass. Prespray with KB-4 Pre-Spray 16oz/1gl at 0.5gl/100ft2 (followed by agitation using rake. Dwell 10 min followed by hot water extract with ChemDry Natural IV in tank solution using the XTS Crossover Portable System 3 wet passes at 1.0ft/sec. |
Chem-Dry®
Logan, UT
435-755-0099
Visit Website
|
|
|
Cintas Carpet Cleaning Systems
Using the 3 step cleaning process, the first step is to vacuum with the V-HDU14 four passes at 1.8 ft/sec. The second step is pre-spray with CFS 6oz/1gl at 1.0 gl/200 ft2 followed by agitation using a cylindrical rotating brush system 2 passes at 1.8ft/sec. Allow 10 minutes dwell time. The final step is to hot water extract with CFS Fiber Rinse 32oz/5gl at 2gl/hr using 2 wet extraction passes followed by 1 dry extraction pass at a rate of 1ft/sec on each pass. Extractor Equipment Aerotech ADM Series Truck Mount with PMF Low Boy Wand. |
Cintas by Complete Floor Solutions
Cincinnati, OH
513-659-3401
|
|
|
Complete Floor Solutions Cleaning Systems
Using the 3 step cleaning process, the first step is to vacuum with the Riccar 880c unit four passes at 1.8 ft/sec. The second step is pre-spray with CFS 6oz/1gl at 1.0 gl/200 ft2 .
Allow 10 minutes dwell time. The final step is to hot water extract with CFS Fiber Rinse 32oz/5gl at 2gl/hr using 3 wet extraction passes at 700 psi followed by 1 dry extraction pass at a rate of 1ft/sec on each pass. Extractor Equipment Aerotech ADM Series Truck Mount with Zipper Wand. |
Cintas by Complete Floor Solutions
Cincinnati, OH
513-659-3401
|
|
Hydro-Force System
Each sample is cleaned using a 3 step cleaning process. The first step is to pre-vacuum with the ProTeam 1500XP Upright four passes at 1.8ft/sec. The second step is to prespray with Bridgepoint Zone Perfect Prespray 6oz/1gl at 1.0gl/200ft2 followed by agitation using a Grandi Groom carpet rake. Allow to dwell for 10 minutes prior to cleaning. The third step is to hot water extract the samples with Bridgepoint End Zone 2oz/gl using 3 wet extraction passes followed by 1 dry extraction pass at a rate of 1 ft/sec on each pass. |
Hydro-force Manufacturing
Salt Lake City, UT
800-658-5314
Visit Website
|
|
Karcher BRC 38/30 C
Step 1 – pre-vacuum with the Karcher CV Upright Vacuum Cleaner 4 passes at 1.8 ft/sec. Pre-spray with Prochem Ultrapac Traffic Clean (6oz/1gl @ 1.0gl/200 sq ft) followed by agitation using carpet rake. Dwell 10 min followed by hot water extract with water only using 3 wet passes followed by 1 dry pass at rate of 1.0ft/sec. |
Karcher
Englewood, CO
800-444-7654
Visit Website
|
|
Karcher BRC 46/38 C
Step 1 – pre-vacuum with the Karcher CV Upright Vacuum Cleaner 4 passes at 1.8 ft/sec. Karcher BRC 46/38 C with Prochem Ultrapac Traffic Clean (6oz/1gl at 1.0gl/200 sq ft) followed by agitation using a carpet rake. Dwell 10 min followed with hot water extract using 3 wet passes and 1 dry at a rate of 1 ft/sec. |
Karcher
Englewood, CO
800-444-7654
Visit Website
|
|
Karcher BRC 46/76 W
Step 1 – pre-vacuum with the Karcher CV Upright Vacuum Cleaner 4 passes at 1.8 ft/sec. Pre-spray with Prochem Ultrapac Traffic Clean (6oz/1gl @ 1.0gl/200 sq ft) followed by agitation using carpet rake. Dwell 10 min followed by hot water extract with water only using 3 wet passes followed by 1 dry pass at rate of 1.0ft/sec. |
Karcher
Englewood, CO
800-444-7654
Visit Website
|
|
Karcher Puzzi 100
Pre-vacuum soiled carpet with Karcher CV Upright vacuum cleaner 4 passes @ 1.8 ft/sec. Pre-spray carpet with Prochem Ultrapac Trafficlean Pre-Spray (6 ounces per gallon applied at 1.0g per 200sqft.). Agitate carpet pile with Gandigroom carpet rake. Allow 10 minutes dwell prior to cleaning with Puzzi 100 unit using hot water only for three wet cleaning passes and one dry at rate of 1.0 ft./sec. |
Karcher
Englewood, CO
800-444-7654
Visit Website
|
|
Karcher Puzzi 8/1
Pre-vacuum soiled carpet with Karcher CV Upright vacuum cleaner 4 passes @ 1.8 ft/sec. Pre-spray carpet with Prochem Ultrapac Trafficlean Pre-Spray (6 ounces per gallon applied at 1.0g per 200sqft.). Agitate carpet pile with Gandigroom carpet rake. Allow 10 minutes dwell prior to cleaning with Puzzi 8/1 unit using hot water only for three wet cleaning passes and one dry at rate of 1.0 ft./sec |
Karcher
Englewood, CO
800-444-7654
Visit Website
|
|
|
C4 Quick Dry Carpet Express w/0.4 Tips
Clean using a 3 step cleaning process. The first step is pre-vacuum with a CRI approved vacuum cleaner 4 passes at 1.8ft/sec. The second step is to pre-spray with the Kent 7-in-1 RTU Pre-Spray at 1.0gl/200ft2. Allow to dwell for 10 minutes prior to cleaning. The third step is to hot water extract with C4 Extractor using Kent 7-in-1 Carpet Care Pro-Formula 8 oz/gl using 2 wet extraction passes at a rate of 0.5ft/sec on each pass. |
Kent Investment Corp.
Ash Flat, AR
800-573-8066
|
|
Mighty Pack® with Rug Doctor Oxy-Steam® 2X
Mighty Pack® with Oxy-Steam® 2X Cleaner solution diluted 4 oz / gl
Procedure: Clean using the Rug Doctor Oxy-Steam® 2x formula diluted 4 oz per gallon with the MightyPack machine 2 wet passes and no dry passes at a rate of 0.6 ft/sec on each pass. |
Rug Doctor
Fenton, MO
800-784-3628
Visit Website
|
|
Mighty Pro® with Rug Doctor Oxy-Steam® 2X
Mighty Pro® with Oxy-Steam® 2X Cleaner solution diluted 4 oz / gl
Procedure: Clean using the Rug Doctor Oxy-Steam® 2x formula diluted 4 oz per gallon with the MightyPro machine 2 wet passes and no dry passes at a rate of 0.6 ft/sec on each pass. |
Rug Doctor
Fenton, MO
800-784-3628
Visit Website
|
|
Mighty Pro™ X3 with Oxy-Steam® Green Cleaner
Mighty Pro™ X3 with Oxy-Steam® Green Cleaner solution diluted 3 oz/gl. Procedure: Rug Doctor 2 step cleaning process. Step 1 – Vacuum prior to cleaning at least 4 passes. Step 2 – Hot water extract with Rug Doctor Oxy-Steam® Green Carpet Cleaner detergent diluted 3 oz per gallon using 2 wet extraction passes at a rate of .7 ft/sec on each pass. |
Rug Doctor
Fenton, MO
800-784-3628
Visit Website
|
|
|
Sears Carpet and Upholstery Care System
Sears Ultratech2 Truck Mount - The first step is pre-vacuum 4 passes at 1.8ft/sec. The second step is to pre-spray with Sears UltraCare Traffic Lane cleaner 6 oz/1gl at 1.0gl/200ft2 followed by agitation using a Gandigroom carpet rake. The treated sample is allowed to dwell for 15 minute prior to cleaning. The third step is to hot water extract the samples with Sears UltraCare Fiber Rinse Carpet Cleaner 32 oz/5gl metered at 2 gl/hr using 3 wet extraction passes followed by 2 dry extraction passes at a rate of 1 ft/sec on each pass. |
Sears Carpet and Upholstery Care
Lewis Center, OH
866-389-4568
Visit Website
|
|
Stanley Steemer''s Truck Mounted Model 5450 with Wand
Stanley Steemer''s Truck Mounted Model 5450 with Proprietary Wand and 2 inch hoses pre-vacuum 4 passes; Prespray with Stanley Steemer 2X concentrate 30:1 as an in-tank rinse using 4 wet passes and 2 dry at 1ft/sec. |
Stanley Steemer International Inc.
Dublin, OH
800-STEEMER
Visit Website
|
|
|
Stanley Steemer’s Truck Mounted Model 5200-5400-5500-5600 with Wand
First Step is to pre-vacuum with the Stanley Steemer Wand 4 passes at 1.8 ft/sec then apply an in-tank pre-spray of SS-G900 (Concentrate of 630:1) using the Stanley Steemer Wand on a forward stroke. Third step is to clean with Stanley Steemer SS-G900 (Concentrate of 630:1) as an in-tank rinse using 3 wet extraction passes followed by 2 dry extraction passes at a rate of 1ft/sec on each pass. |
Stanley Steemer International Inc.
Dublin, OH
800-STEEMER
Visit Website
|
|
TCS Warrior 18
The first step is to pre-vacuum with the Nilfisk GU 15 SMU, or any CRI approved vacuum, four passes at 1.8ft/sec. The second step is to pre-spray with MAXX Pre-Spray 4oz/1gl at 1gl/200ft squared followed by agitation using a Gandigroom carpet rake. The treated carpet is allowed to dwell for 10 minutes prior to cleaning. The third step is to hot water extract the carpet with the TCS Warrior 18 truck mount using 2 wet extraction passes followed by 2 dry extraction passes at a rate of 1ft/sec on each pass. |
Truckmounts and Cleaning Solutions
Norcross, GA
770-729-7117
Visit Website
|
|
Unisource FastBreak 10
Unisource FastBreak 10 with Prochem Ultrapac Traffic Clean
(6oz/1gl at 1.0gl/200 sq ft) |
Unisource Worldwide, Inc.
Norcross, GA
800-UNISOURCE
Visit Website
|
|
Unisource FastBreak 20
Fast Break 20 using Prochem Ultrapac Trafficlean (6oz/1gl at 1.0gl/200 sq ft) |
Unisource Worldwide, Inc.
Norcross, GA
800-UNISOURCE
Visit Website
|
|
Unisource FastBreak 8
Unisource FastBreak 8 walk behind system Prochem Ultrapac Traffic Clean (6oz/1gl at 1.0gl/200 sq ft) |
Unisource Worldwide, Inc.
Norcross, GA
800-UNISOURCE
Visit Website
|
|
Commodore 20
Pre-spray with Prochem Ultrapac Trafficclean 6oz/1gl @ 1.0gl/200 sq ft. followed by agitation using a carpet rake. Dwell 10 min followed by hot water extract with water using 3 wet passes and 1 dry at a rate of 1ft/sec. |
Windsor
Englewood, CO
800-444-7654
Visit Website
|
|
Priza
Pre-vacuum soiled carpet with Windsor Versamatic vacuum cleaner 4 passes @ 1.8 ft/sec. Pre-spray carpet with Prochem Ultrapac Trafficlean Pre-Spray (6 ounces per gallon applied at 1.0g per 200sq ft.). Agitate carpet pile with Gandigroom carpet rake. Allow 10 minutes dwell prior to cleaning with Priza unit using hot water only for three wet cleaning passes and one dry at rate of 1.0 ft./sec |
Windsor
Englewood, CO
800-444-7654
Visit Website
|
|
Windsor Cadet CDT7
Pre-vacuum with Windsor Versamatic vacuum cleaner 4 passes at 1.8ft/sec. Pre-spray with Prochem Ultrapac Traffic Clean (6oz/1gl @ 1.0gl/200 sq ft) followed by agitation using carpet rake. Dwell 10 min followed by hot water extract with water only using 3 wet passes followed by 1 dry pass at rate of 1.0ft/sec. |
Windsor
Englewood, CO
800-444-7654
Visit Website
|
|
Windsor Clipper CLP12
Pre-spray with Prochem Ultrapac Traffic Clean (6oz/1gl @ 1.0gl/200 sq ft) followed by agitation using carpet rake. Dwell 10 min followed by hot water extract with water only using 3 wet passes followed by 1 dry extraction pass at rate of 1.0ft/sec. |
Windsor
Englewood, CO
800-444-7654
Visit Website
|
|
Windsor Clipper Duo
Pre-spray with Prochem Ultrapac Traffic Clean (6oz/1gl @ 1.0gl/200 sq ft) followed by agitation using carpet rake. Dwell 10 min followed by hot water extract with water only using 3 wet passes followed by 1 dry extraction pass at rate of 1.0ft/sec. |
Windsor
Englewood, CO
800-444-7654
Visit Website
|
|
| |
Model/Solution Configuration |
Provider/Manufacturer |
|
Fiberpro 8 FP8
Pre-spray with FiberPRO® TLC Traffic Lane Cleaner (6oz/1gl @ 1.0gl/200 sq ft) followed by agitation using carpet rake. Dwell 10 min followed by hot water extract with water only using 3 wet passes followed by 1 dry extraction pass at rate of 1.0ft/sec. |
Betco Corporation
Toledo, OH
888-462-3826
Visit Website
|
|
Fiberpro FP20
Pre-spray with FiberPRO® TLC Traffic Lane Cleaner (6oz/1gl @ 1.0gl/200 sq ft) followed by agitation using a carpet rake. Dwell 10 min followed by hot water extract with water using 3 wet passes and 1 dry at a rate of 1ft/sec. |
Betco Corporation
Toledo, OH
888-462-3826
Visit Website
|
|
Bridgepoint System
Pre-spray with ZonePerfect mixed 6 oz/gl of water. Apply at rate of 200 sq. ft. per diluted gallon of water. Agitate with grooming tool and allow to dwell 10 minutes. Extract using HydraMaster Boxxer XL Truck Mount utilizing RX20 Rotary Extraction Wand utilizing two wet passes followed by 1 dry pass at 1 ft/sec. Use EndZone as in-tank extraction solution mixed 1 qt/5 gl in solution tank of truck mount. Set truck mount solution flow meter on 2-3. |
Bridgepoint Systems
Salt Lake City, UT
800-658-5314
Visit Website
|
|
Dustbane 1000 XT
Pre-spray with Prochem Ultrapac Traffic Clean (6oz/1gl @ 1.0gl/200 sq ft) followed by agitation using carpet rake. Dwell 10 min followed by hot water extract with water only using 3 wet passes followed by 1 dry extraction pass at rate of 1.0ft/sec. |
Dustbane Products Limited
Ottawa, Ontario
613-745-6861
Visit Website
|
|
Dustbane 800 XT Extractor
Pre-spray with Prochem Ultrapac Traffic Clean (6oz/1gl @ 1.0gl/200 sq ft) followed by agitation using carpet rake. Dwell 10 min followed by hot water extract with water only using 3 wet passes followed by 1 dry extraction pass at rate of 1.0ft/sec. |
Dustbane Products Limited
Ottawa, Ontario
613-745-6861
Visit Website
|
|
Millicare Hot Water Extraction Cleaning System
The first step is to pre-vacuum with the Windsor Versamatic vacuum cleaner 4 passes a 1.8ft/sec. The second step is to pre-spray with MilliCare V4 Pre-Mist at a rate of 1gal per 200 sq ft). The third step is to agitate the MilliCare V4 Pre-mist into the carpet with the MilliCare 2000 scrubber, 2 passes at 1.8 ft per sec. Use appropriate brushes on the scrubber suited to the construction and grade of the carpet. Allow 10 minute dwell time. Hot water extract the carpet using the Windsor Clipper extractor using 2 wet passes and one dry at 1.0 ft per sec with hot water only in the tank. |
MilliCare Textile and Carpet Care
LaGrange, GA
888-886-2273
Visit Website
|
|
Mohawk Floorcare Essentials System
Mohawk Truck mount 4.8 CVS Prespray with Mohawk Traffic Lane Pre-Spray 8oz/1gl at 1.2gl/100 sq ft followed by agitation using rake. Dwell 10 min followed by hot water extract with Mohawk Carpet Cleaner using 2 wet passes and 4 dry at 1ft/sec. |
Mohawk FloorCare
Fayetteville, GA
800-554-6637
Visit Website
|
|
PowrFlite Model 98150-PF
PowrFlite Model 98150-PF Carpet Extractor using HHED-G Carpet Detergent Tacony 3 step cleaning process. The first step is to pre-vacuum using the PowrFlite upright vacuum cleaner 4 passes at 1.8ft/sec. The second step is to pre-spray with HHED-G Pre-Spray at 24 oz/80ft2. The treated sample is allowed to dwell for 10 minutes prior to cleaning. The third step is to hot water extract the samples with the PowrFlite Model 98150-PF Carpet Extractor using 2 wet extraction passes followed by 2 dry extraction passes at a rate of 1ft/sec on each pass using the HHED-G in-tank solution diluted 1 oz/gl. |
PowrFlite – Div of Tacony
Ft. Worth, TX
800-880-2913
Visit Website
|
|
Everest 650
Everest 650 Truck Mount (6oz/1gl at 1.0gl/200 sq ft) Pre-vacuum using four passes at 1.8ft/sec Pre-spray with Axiom Clean Prespray 6oz/gl water. Apply at rate of 200 sq ft per diluted gallon of water. Agitate with rake. Dwell 10 min followed by hot water extract with Axiom Clean Free Rinse (1.5 qt/5gl). Extract carpet with Quad Jet Wand, using 2 wet passes and 2 dry at 1ft/sec. |
Prochem
Chandler, AZ
800-776-2436
Visit Website
|
|
|
Everest 650
Everest 650 Truck Mount (6oz/1gl at 1.0gl/200 sq ft) Pre-vacuum using four passes at 1.8ft/sec Pre-spray with Axiom Clean Prespray 6oz/gl water. Apply at rate of 200 sq ft per diluted gallon of water. Agitate with rake. Dwell 10 min followed by hot water extract Dilute Axiom Clean Extraction Detergent (1qt/5gl). Extract carpet with Quad Jet Wand, using 2 wet passes and 2 dry at 1ft/sec. |
Prochem
Chandler, AZ
800-776-2436
Visit Website
|
|
|
Everest 650
Everest 650 Truck Mount (6oz/1gl at 1.0gl/200 sq ft) Pre-spray with Prochem Ultrapac Pre-Treat with LVC (S903) Concentrate at 1.2gl/100 sqft. Agitate with rake. Dwell 10 min followed by hot water extract with Prochem All Fiber Rinse (B109) using 2 wet passes and 2 dry at 1ft/sec. |
Prochem
Chandler, AZ
800-776-2436
Visit Website
|
|
|
Everest 650
Everest 650 Truck Mount (6oz/1gl at 1.0gl/200 sq ft) Pre-vacuum using four passes at 1.8ft/sec Pre-spray with Peaches n Clean Traffic Lane Cleaner 6oz/gl water. Apply at rate of 200 sq ft per diluted gallon of water. Agitate with rake. Dwell 10 min followed by hot water extract with Peaches n Clean Free Rinse (1.5 qt/5gl). Extract carpet with Quad Jet Wand, using 2 wet passes and 2 dry at 1ft/sec. |
Prochem
Chandler, AZ
800-776-2436
Visit Website
|
|
Mighty Pack® with Rug Doctor Steam Cleaner
Each sample is cleaned using the Rug Doctor 2 step cleaning process.
The first step is to vacuum the carpet prior to cleaning at least 4 passes. The second step is to hot water extract the samples using the Mighty Pack® extractor with the Rug Doctor Steam Cleaner detergent diluted to 4 oz per gallon using 4 wet extraction passes at a rate of 1ft/sec on each pass. |
Rug Doctor
Fenton, MO
800-784-3628
Visit Website
|
|
Mighty Pro® with Rug Doctor Steam Cleaner
Each sample is cleaned using the Rug Doctor 2 step cleaning process. The first step is to vacuum the carpet prior to cleaning at least 4 passes. The second step is to hot water extract the samples using the Mighty Pro® extractor with the Rug Doctor Steam Cleaner detergent diluted to 4 oz per gallon using 4 wet extraction passes at a rate of 1ft/sec on each pass. |
Rug Doctor
Fenton, MO
800-784-3628
Visit Website
|
|
Sears Ultratech
Sears Ultratech Truck Mount (6oz/1gl at 1.0gl/200 sq ft) Pre-vacuum using four passes at 1.8ft/sec Pre-spray with UltraCare Green Traffic Lane Cleaner 6oz/gl water. Apply at rate of 200 sq ft per diluted gallon of water. Agitate with rake. Dwell 10 min followed by hot water extract with UltraCare Green Fiber Rinse (1.5 qt/5gl). Extract carpet with Quad Jet Wand, using 2 wet passes and 2 dry at 1ft/sec. |
Sears Carpet and Upholstery Care
Lewis Center, OH
866-389-4568
Visit Website
|
|
|
Sears Ultratech
Sears Ultratech Truck Mount (6oz/1gl at 1.0gl/200 sq ft) Pre-vacuum using four passes at 1.8ft/sec Pre-spray with Axiom Clean Prespray 6oz/gl water. Apply at rate of 200 sq ft per diluted gallon of water. Agitate with rake. Dwell 10 min followed by hot water extract Dilute Axiom Clean Extraction Detergent (1qt/5gl). Extract carpet with Quad Jet Wand, using 2 wet passes and 2 dry at 1ft/sec. |
Sears Carpet and Upholstery Care
Lewis Center, OH
866-389-4568
Visit Website
|
|
Steamin Demon Classic
Portable extractor. Pre-spray with Demon Clean 1.2gl/100 sq ft. Agitate with grooming brush and let dwell 10 min followed by hot water extract at a flow rate of 3 gpm. |
Steamin Demon Inc.
Clarksville, IN
888-413-6748
Visit Website
|
|
|
Steamin Demon HP
Portable extractor. Pre-spray with Demon Clean 1.2gl/100 sq ft. Agitate with grooming brush and let dwell 10 min followed by hot water extract at a flow rate of 3 gpm. |
Steamin Demon Inc.
Clarksville, IN
888-413-6748
Visit Website
|
|
Steamin Demon XL15
Portable extractor. Pre-spray with Demon Clean 1.2gl/100 sq ft. Agitate with grooming brush and let dwell 10 min followed by hot water extract at a flow rate of 3 gpm. |
Steamin Demon Inc.
Clarksville, IN
888-413-6748
Visit Website
|
|
Steamin Demon XL20
Portable extractor. Pre-spray with Demon Clean 1.2gl/100 sq ft. Agitate with grooming brush and let dwell 10 min followed by hot water extract at a flow rate of 3 gpm. |
Steamin Demon Inc.
Clarksville, IN
888-413-6748
Visit Website
|
|
Ace Hardware Model 98150-ACE Carpet Extractor
Ace Hardware Model 98150-ACE Carpet Extractor using HHED-G Carpet Detergent Tacony 3 step cleaning process. The first step is to pre-vacuum using the PowrFlite upright vacuum cleaner 4 passes at 1.8ft/sec. The second step is to pre-spray with HHED-G Pre-Spray at 24 oz/80ft2. The treated sample is allowed to dwell for 10 minutes prior to cleaning. The third step is to hot water extract the samples with the Ace Hardware Model 98150-ACE Carpet Extractor using 2 wet extraction passes followed by 2 dry extraction passes at a rate of 1ft/sec on each pass using the HHED-G in-tank solution diluted 1 oz/gl. |
Tacony Corporation
Fenton, MO
636-349-3000
Visit Website
|
|
Riccar Carpet Extractor RCE using HHED-G Carpet Detergent
Tacony 3 step cleaning process. The first step is to pre-vacuum using the PowrFlite upright vacuum cleaner 4 passes at 1.8ft/sec. The second step is to pre-spray with RPF-T Pre-Spray at 24 oz/80ft2. The treated sample is allowed to dwell for 10 minutes prior to cleaning. The third step is to hot water extract the samples with the Riccar Carpet Extractor using 2 wet extraction passes followed by 2 dry extraction passes at a rate of 1ft/sec on each pass using the HHED-G in-tank solution diluted 1 oz/gl. |
Tacony Corporation
Fenton, MO
636-349-3000
Visit Website
|
|
Simplicity Carpet Extractor SCE using HHED-G Carpet Detergent
Tacony 3 step cleaning process. The first step is to pre-vacuum using the PowrFlite upright vacuum cleaner 4 passes at 1.8ft/sec. The second step is to pre-spray with HHED-G Pre-Spray at 24 oz/80ft2. The treated sample is allowed to dwell for 10 minutes prior to cleaning. The third step is to hot water extract the samples with the Simplicity Carpet Extractor using 2 wet extraction passes followed by 2 dry extraction passes at a rate of 1ft/sec on each pass using the HHED-G in-tank solution diluted 1 oz/gl. |
Tacony Corporation
Fenton, MO
636-349-3000
Visit Website
|
|
Tornado Mini Marathon Model 98150
Tornado Mini Marathon Model 98150 Carpet Extractor using HHED-G Carpet Detergent
Tacony 3 step cleaning process. The first step is to pre-vacuum using the PowrFlite upright vacuum cleaner 4 passes at 1.8ft/sec. The second step is to pre-spray with HHED-G Pre-Spray at 24 oz/80ft2. The treated sample is allowed to dwell for 10 minutes prior to cleaning. The third step is to hot water extract the samples with the Tornado Mini Marathon Model 98150 Carpet Extractor using 2 wet extraction passes followed by 2 dry extraction passes at a rate of 1ft/sec on each pass using the HHED-G in-tank solution diluted 1 oz/gl. |
Tornado – Div of Tacony
Fenton, MO
636-349-3000
Visit Website
|
|
|
True Clean Super System
System utilizes a two step process. First step is prespray with True Clean SS at 1.0 gallon per 100sq ft. The treated area is allowed to dwell for 5 minutes prior to cleaning. Second step is hot water extract with Hydramaster RDM wand using 4 wet extraction passes at 1ft. per second. |
True Clean Carpet. LLC
St. Peters, MO
877-220-2532
Visit Website
|
|
Agitator 20® System
Self-contained extractor - Pre-vacuum using four passes. Pre-spray with Prochem Ultrapac 1gl/200 sq ft. Dwell 10 min followed by hot water extract using 2 wet passes and 2 dry in accordance with AG-20 instructions |
U.S. Products
Mukilteo, WA
800-257-7982
Visit Website
|
|
Admiral 8 Extractor
Pre-spray with Prochem Ultrapac Traffic Clean (6oz/1gl @ 1.0gl/200 sq ft) followed by agitation using carpet rake. Dwell 10 min followed by hot water extract with water only using 3 wet passes followed by 1 dry extraction pass at rate of 1.0ft/sec. |
Windsor
Englewood, CO
800-444-7654
Visit Website
|
|
| |
Model/Solution Configuration |
Provider/Manufacturer |
|
Ninja 1.007-068.0, AquaFoil Wand 8.632-900.0 , ProChem Ultrapac Trafficlean, Windsor Versamatic
Step 1 – pre-vacuum with the Windsor Versamatic Vacuum Cleaner 4 passes at 1.8 ft/sec. Step 2 – Pre-spray with Prochem Ultrapac Trafficlean Pre-spray (6oz/1gl at 1.0 gl/200ft2) Agitate carpet pile with carpet rake. Allow to dwell for 10 minutes prior to cleaning. Step 3 – Hot Water Extract with Ninja 1.007-068.0 using water only – 2 wet cleaning passes and one dry at rate of 1.0ft/sec. |
Century 400
Chandler, AZ
800-752-1777
|
|
CFR ECO-500 System
Using Tacony 3 step cleaning process. The first step is to pre-vacuum using the CFR Pro-Lite vacuum cleaner 4 passes at 1.8ft/sec. The second step is to pre-spray with CFR A Excell Solutions at 20 oz/1 gl at 1 gl/200ft2. The treated sample is allowed to dwell for 10 minutes prior to cleaning. The final step is to hot water extract with the CFR A Excell solution 1 oz/gl using 4 wet extraction passes at a rate of 1ft/sec on each pass. |
CFR (Division of Tacony)
Fort Worth, TX
800-533-2557
Visit Website
|
|
E1720-10, AquaFoil 2 Jet Wand 110-01, Esteam Suspend Concentrated Prespray, Windsor Versamatic
Step 1 – pre-vacuum with the Windsor Versamatic Vacuum Cleaner 4 passes at 1.8 ft/sec. Step 2 – Pre-spray with Esteam Suspend Concentrated Carpet Pre-spray (6oz/1gl/200ft2) followed by agitation using a Gandigroom carpet rake. Allow to dwell for 10 minutes prior to cleaning. Step 3 – Hot water extract with E1720-10 using water only - 2 wet extraction passes and two dry passes at a rate of 1.0flt/sec on each pass. |
Esteam Mfg
Calgary, Alberta
403-291-7050
Visit Website
|
|
Ninja Warrior 500-10, AquaFoil 2 Jet Wand 110-01, Esteam Suspend Concentrated Prespray, Windsor Versamatic
Step 1 – pre-vacuum with the Windsor Versamatic Vacuum Cleaner 4 passes at 1.8 ft/sec. Step 2 – Pre-spray with Esteam Suspend Concentrated Carpet Pre-spray (6oz/1gl/200ft2) followed by agitation using a Gandigroom carpet rake. Allow to dwell for 10 minutes prior to cleaning. Step 3 – Hot water extract with Ninja 500-10 using water only - 2 wet extraction passes and two dry passes at a rate of 1.0flt/sec on each pass. |
Esteam Mfg
Calgary, Alberta
403-291-7050
Visit Website
|
|
Kaivac No Touch Cleaning
Kaivac KV1250, Wespak 2Jet and Kaivac Multi-purpose Cleaner, Vacuum 4 passes at 1.8ft/sec using the Kaivac turbine floor tool. Then pre-spray with Kaivac
Multi-purpose cleaner 1gl/200ft2 at 2oz/1gl. Allow to dwell for 5 minutes prior to cleaning.
Water extract with the Kaivac KV1250 extractor using 2 wet extraction passes followed by 2 Dry extraction passes at a rate of 1ft/sec on each pass. |
Kaivac
Hamilton, OH
513-887-4600
Visit Website
|
|
Kaivac No Touch Cleaning
Kaivac KV1750, Wespak 2Jet and Kaivac Multi-purpose Cleaner, Vacuum 4 passes at 1.8ft/sec using the Kaivac turbine floor tool. Then pre-spray with Kaivac Multi-purpose cleaner 1gl/200ft2 at 2oz/1gl. Allow to dwell for 5 minutes prior to cleaning. Water extract with the Kaivac KV1750 extractor using 2 wet extraction passes followed by 2 Dry extraction passes at a rate of 1ft/sec on each pass. |
Kaivac
Hamilton, OH
513-887-4600
Visit Website
|
|
Kaivac No Touch Cleaning
Kaivac KV2150, Wespak 2Jet and Kaivac Multi-purpose Cleaner, Vacuum 4 passes at 1.8ft/sec using the Kaivac turbine floor tool. Then pre-spray with Kaivac Multi-purpose cleaner 1gl/200ft2 at 2oz/1gl. Allow to dwell for 5 minutes prior to cleaning. Water extract with the Kaivac KV2150 extractor using 2 wet extraction passes followed by 2 Dry extraction passes at a rate of 1ft/sec on each pass. |
Kaivac
Hamilton, OH
513-887-4600
Visit Website
|
|
Karcher BRC 30/15
Step 1 – pre-vacuum with the Karcher CV Upright Vacuum Cleaner 4 passes at 1.8 ft/sec. Step 2 – Pre-spray with Prochem Ultrapac Trafficlean Pre-spray (6oz/1gl at 1.0 gl/200ft2). Agitate carpet pile with carpet rake. Allow 10 minutes dwell prior to cleaning with BRC 30/15 using water only for three wet cleaning passes and one dry pass at a rate of 1.0flt/sec on each pass. |
Karcher
Englewood, CO
800-444-7654
Visit Website
|
|
Karcher Puzzi 50-35 E (1.006-672.0)
Kurve 2-Jet Wand 110-011 ProChem Ultrapac Trafficclean, Karcher CV Upright Vacuum, Step 1 - Pre-vacuum with the Karcher CV Upright vacuum cleaner 4 passes @ 1.8 ft/sec. Step 2 - Pre-spray carpet with Prochem Ultrapac Trafficlean Pre-Spray (6 ounces per gallon applied at 1.0g per 200sqft.) followed by agitation using a Gandigroom carpet rake. Allow 10 minutes dwell prior to cleaning. Step 3 - Hot water extract with water only using two wet extraction passes and two dry at rate of 1.0 ft./sec |
Karcher
Englewood, CO
800-444-7654
Visit Website
|
|
|
Karcher Puzzi 64/35E (1.006-674.0)
Karcher Puzzi 1.006-674.0, Kurve 2-Jet Wand 110-01. Step 1 – pre-vacuum with the Karcher CV Upright Vacuum Cleaner 4 passes at 1.8 ft/sec. Step 2 – Pre-spray with Prochem Ultrapac Trafficlean Pre-spray (6oz/1gl at 1.0 gl/200ft2) followed by agitation using a Gandigroom carpet rake. Allow to dwell for 10 minutes prior to cleaning. Step 3 – Hot water extract with water only using 2 wet extraction passes 2 dry pass at a rate of 1.0ft/sec on each pass. |
Karcher
Englewood, CO
800-444-7654
Visit Website
|
|
|
Karcher Puzzi Karcher Puzzi 50/14E (1.006-673.0)
Karcher Puzzi 1.006-673.0, Kurve 2-Jet Wand 110-01. Step 1 – pre-vacuum with the Karcher CV Upright Vacuum Cleaner 4 passes at 1.8 ft/sec. Step 2 – Pre-spray with Prochem Ultrapac Trafficlean Pre-spray (6oz/1gl at 1.0 gl/200ft2) followed by agitation using a Gandigroom carpet rake. Allow to dwell for 10 minutes prior to cleaning. Step 3 – Hot water extract with water only using 2 wet extraction passes 2 dry pass at a rate of 1.0ft/sec on each pass. |
Karcher
Englewood, CO
800-444-7654
Visit Website
|
|
Nobles EX15 System
Each sample is cleaned using the Nobles EX15 cleaning process. The first step is to vacuum 4 passes at 1.8ft/sec with the Nobles TV1200 12” vacuum. The next step is to pre-spray with Tennant ReadySpace pre-Treatment 8oz/1gl at 1gl/400ft2. The treated sample is allowed to dwell for 10 minutes prior to cleaning. The following step is to hot water extract the samples with Nobles EX15 using 2 wet extraction passes and 2 dry passes at a rate of 50ft/min on each pass. |
Nobles Industries (Tennant Co.)
Holland, MI
800-510-0616
Visit Website
|
|
Tennant E5 System
Each sample is cleaned using the Tennant E5 cleaning process. The first step is to vacuum 4 passes at 1.8ft/sec with the Tennant 3200 vacuum. The next step is to pre-spray with Tennant ReadySpace pre-Treatment 8oz/1gl at 1gl/400ft2. The treated sample is allowed to dwell for 10 minutes prior to cleaning. The following step is to hot water extract the samples with Tennant E5 using 2 wet extraction passes and 2 dry passes at a rate of 50ft/min on each pass. |
Tennant Co.
Minneapolis, MN
800-553-8033
Visit Website
|
|
Chariot (CE24)
Pre-vacuum soiled carpet with Windsor Versamatic vacuum cleaner 4 passes @ 1.8 ft/sec. Pre-spray carpet with Prochem Ultrapac Trafficlean Pre-Spray (6 ounces per gallon applied at 1.0g per 200sq ft.). Agitate carpet pile with Gandigroom carpet rake. Allow 10 minutes dwell prior to cleaning with Windsor Chariot using hot water only for three wet cleaning passes and one dry at rate of .75 ft./sec |
Windsor
Englewood, CO
800-444-7654
Visit Website
|
|
Commodore Duo
(Restorative Mode) Pre-vacuum soiled carpet with Windsor Versamatic vacuum cleaner 4 passes @ 1.8 ft/sec. Pre-spray carpet with Prochem Ultrapac Trafficlean Pre-Spray (6 ounces per gallon applied at 1.0g per 200sq ft.). Agitate carpet pile with Gandigroom carpet rake. Allow 10 minutes dwell prior to cleaning with Commodore Duo using hot water only for two wet cleaning passes and two dry at rate of 1.4 ft./sec |
Windsor
Englewood, CO
800-444-7654
Visit Website
|
|
Dominator 1.006-665.0, AquaFoil 2 Jet Wand 110-01, ProChem Ultrapac Trafficlean, Windsor Versamatic
Step 1 – pre-vacuum with the Windsor Versamatic Vacuum Cleaner 4 passes at 1.8 ft/sec.
Step 2 – Pre-spray with Prochem Ultrapac Trafficlean Pre-spray (6oz/1gl at 1.0 gl/200ft2) followed by agitation using a Gandigroom carpet rake. Allow to dwell for 10 minutes prior to cleaning.
Step 3 – Hot water extract with water only using 2 wet extraction passes 2 dry pass at a rate of 1.0flt/sec on each pass. |
Windsor
Englewood, CO
800-444-7654
Visit Website
|
|
|
Dominator 1.006-667.0, AquaFoil 2 Jet Wand 110-01, ProChem Ultrapac Trafficlean, Windsor Versamatic
Step 1 – pre-vacuum with the Windsor Versamatic Vacuum Cleaner 4 passes at 1.8 ft/sec.
Step 2 – Pre-spray with Prochem Ultrapac Trafficlean Pre-spray (6oz/1gl at 1.0 gl/200ft2) followed by agitation using a Gandigroom carpet rake. Allow to dwell for 10 minutes prior to cleaning.
Step 3 – Hot water extract with water only using 2 wet extraction passes 2 dry pass at a rate of 1.0flt/sec on each pass. |
Windsor
Englewood, CO
800-444-7654
Visit Website
|
|
|
Dominator 1.006-668.0, AquaFoil 2 Jet Wand 110-01, ProChem Ultrapac Trafficlean, Windsor Versamatic
Step 1 – pre-vacuum with the Windsor Versamatic Vacuum Cleaner 4 passes at 1.8 ft/sec.
Step 2 – Pre-spray with Prochem Ultrapac Trafficlean Pre-spray (6oz/1gl at 1.0 gl/200ft2) followed by agitation using a Gandigroom carpet rake. Allow to dwell for 10 minutes prior to cleaning.
Step 3 – Hot water extract with water only using 2 wet extraction passes 2 dry pass at a rate of 1.0flt/sec on each pass. |
Windsor
Englewood, CO
800-444-7654
Visit Website
|
|
|
Dominator 1.006-669.0, AquaFoil 2 Jet Wand 110-01, ProChem Ultrapac Trafficlean, Windsor Versamatic
Step 1 – pre-vacuum with the Windsor Versamatic Vacuum Cleaner 4 passes at 1.8 ft/sec.
Step 2 – Pre-spray with Prochem Ultrapac Trafficlean Pre-spray (6oz/1gl at 1.0 gl/200ft2) followed by agitation using a Gandigroom carpet rake. Allow to dwell for 10 minutes prior to cleaning.
Step 3 – Hot water extract with water only using 2 wet extraction passes 2 dry pass at a rate of 1.0flt/sec on each pass. |
Windsor
Englewood, CO
800-444-7654
Visit Website
|
|
Mini-Pro
Pre-vacuum soiled carpet with Windsor Versamatic vacuum cleaner 4 passes. Pre-spray carpet with Prochem Ultrapac Trafficlean Pre-Spray (6 ounces per gallon applied at 1.0g per 200sq ft.). Agitate carpet pile with carpet rake. Allow 10 minutes dwell prior to cleaning with Mini-Pro using water only for three wet cleaning passes and one dry at rate of 1.0 ft./sec. |
Windsor
Englewood, CO
800-444-7654
Visit Website
|
|
|
Ninja 1.007-068.0, AquaFoil 2 Jet Wand 110-01, ProChem Ultrapac Trafficlean, Windsor Versamatic
Step 1 – pre-vacuum with the Windsor Versamatic Vacuum Cleaner 4 passes at 1.8 ft/sec.
Step 2 – Pre-spray with Prochem Ultrapac Trafficlean Pre-spray (6oz/1gl at 1.0 gl/200ft2) followed by agitation using a Gandigroom carpet rake. Allow to dwell for 10 minutes prior to cleaning.
Step 3 – Hot water extract with water only using 2 wet extraction passes 2 dry pass at a rate of 1.0flt/sec on each pass. |
Windsor
Englewood, CO
800-444-7654
Visit Website
|
|
Voyager Duo
(Restorative Mode) Pre-vacuum soiled carpet with Windsor Versamatic vacuum cleaner 4 passes @ 1.8 ft/sec. Pre-spray carpet with Prochem Ultrapac Trafficlean Pre-Spray (6 ounces per gallon applied at 1.0g per 200sq ft.). Agitate carpet pile with Gandigroom carpet rake. Allow 10 minutes dwell prior to cleaning with Voyager Duo using hot water only for three wet cleaning passes and one dry at rate of 1.4 ft./sec |
Windsor
Englewood, CO
800-444-7654
Visit Website
|
|
| |
Model/Solution Configuration |
Provider/Manufacturer |
|
ES4000 Total Carpet Care System
The first step is to pre-vacuum with the Advance ES4000 using Dry Sweep Mode 1 pass at 108ft/min. The second step is pre-spray with the Advance ES4000 using Pre Treat Mode and 3m #28 Pre-Spray 2 oz/1gl at 1gl/300ft2. The treated sample is allowed to dwell for 10 minutes prior to cleaning. The final step is to extract the samples with Advance ES4000 using Restorative Extraction Mode 2 wet extraction passes at a rate of 50ft/min on each pass. |
Advance
Plymouth, MN
763-745-3500
Visit Website
|
|
Aramark R14 System
Each sample is cleaned using the Aramark R14 cleaning process. The first step is to vacuum 4 passes at 1.8ft/sec with the Tennant 3120 Dual Motor vacuum. The next step is to pre-spray with ReadySpace pre-Treatment 8oz/1gl at 1gl/500ft2. The treated sample is allowed to dwell for 10 minutes prior to cleaning. The following step is to hot water extract the samples with Tennant R14 using 1 wet extraction pass at a rate of 50ft/min on each pass.. |
Aramark Corporation
Downers Grove, IL
1-630-271-2000
Visit Website
|
|
Carpet Cleaner America System
Each sample is cleaned using a 5 step cleaning process. The first step is to pre-vacuum with the Windsor VSP14 four passes at 1.8ft/sec. The second step is to prespray with nKapper prespray 10oz/1gl at 1.0gl/600ft2. The third step is to apply NatraDri compound 2.2lbs per 130sqft. The fourth step is to agitate using the CCA DriStar14 four passes at 1.8ft/sec using the white brushes. The treated sample is allowed to dry 60 minutes prior to pos vacuuming. The final step is to vacuum two passes @ 0.5ft/sec. |
Carpet Cleaner America
Spartanburg, SC
864-576-9887
Visit Website
|
|
CFR Cascade 20 System
Using Tacony 3 step cleaning process. The first step is to pre-vacuum using the CFR Pro-Lite vacuum cleaner 4 passes at 1.8ft/sec. The second step is to pre-spray with CFR A Excell Solutions at 20 oz/1 gl at 1 gl/200ft2. The treated sample is allowed to dwell for 10 minutes prior to cleaning. The final step is to hot water extract with the CFR A Excell solution 1 oz/gl using 1 wet extraction pass followed by 1 dry pass at a rate of 48ft/min on each pass. |
CFR (Division of Tacony)
Fort Worth, TX
800-533-2557
Visit Website
|
|
Diversey Dry Foam Carpet Care System
Using the TASKI by Diversey ergodisc 200 unit with a Foam Generator attachment and a use solution of Diversey Dry Foam Carpet & Upholstery Cleaner. The ergodisc unit will have the black counter balance weight removed. The first step is to pre-vacuum carpet with TASKI Jet vacuum cleaner 2 passes at 1.8ft/sec. The second step is set the Foam Generator setting to “3” for 10 seconds and allow foam to dispense through the dry foam carpet brush. The third step is to clean the carpet with the foam 2 passes at 1 ft/sec and 2 passes 1ft/sec with the foam off. The fourth step is to vacuum after a 30 minute dwell time with the TASKI Jet vacuum cleaner 2 passes at ½ ft/sec. |
Diversey
Sturtevant, WI
53177
Visit Website
|
|
Brush Pro System
Each sample is cleaned using a 5 step cleaning process. The first step is to pre-vacuum with the Windsor VSP14 four passes at 1.8ft/sec. The second step is to prespray with Brush Pro Prespray 10oz/1gl at 1.0gl/600ft2. The third step is to apply Brush Pro Dry Compound 2.2lbs per 130sqft. The fourth step is to agitate using the Hydro-force Brush Pro 17 four passes at 1.8ft/sec using the white brushes. The treated sample is allowed to dry 60 minutes prior to post vacuuming. The final step is to vacuum two passes @ 0.5ft/sec. |
Hydro-force Manufacturing
Salt Lake City, UT
800-658-5314
Visit Website
|
|
BRS 43/500C
The first step is to pre-vacuum with the Windsor Versamatic vacuum cleaner – four passes at 1.8ft/sec. The second step is to pre-spray with ProChem Procap diluted to 8 oz. per gallon of water (do not over wet). The third step – do not allow chemical to dry, agitate with the Windsor iCapsol Mini machine 4 passes at 1.8 ft/sec. The fourth step is to vacuum after a 40 minutes minimum drying time with the Windsor Versamatic vacuum cleaner 4 passes at ½ ft/sec. |
Karcher
Englewood, CO
800-444-7654
Visit Website
|
|
Millicare Pre-Mist NXT and Dry Carpet Cleaner
Each sample is cleaned using the Basic MilliCare Process. The first step is to pre-vacuum with the Windsor Versamatic vacuum cleaner 4 passes a 1.8ft/sec. The second step is to pre-spray with Pre-Mist NXT Pre-Spray (16oz/1gal at 1gl/3000 sq ft). The third step is to spread the MilliCare Dry Carpet Cleaner 1.5lb/100 sq ft onto the misted area followed by agitation with the Whittaker machine (M2000 Scrubber) 2 passes at 1.8ft/sec. The fourth sep is to vacuum after a 30 minute minimum dwell time with the Windsor Versamatic vacuum cleaner 2 passes at 1/2ft/sec. |
MilliCare Textile and Carpet Care
LaGrange, GA
888-886-2273
Visit Website
|
|
|
Millicare V4 Pre-Mist and Dry Carpet Cleaner
Each sample is cleaned using the Basic MilliCare Process. The first step is to pre-vacuum with the Windsor Versamatic vacuum cleaner 4 passes a 1.8ft/sec. The second step is to pre-spray with Pre-Mist Pre-Spray (16oz/1gal at 1gl/3000 sq ft). The third step is to spread the MilliCare Dry Carpet Cleaner 1.5lb/100 sq ft onto the misted area followed by agitation with the Whittaker machine (M2000 Scrubber) 2 passes at 1.8ft/sec. The fourth sep is to vacuum after a 30 minute minimum dwell time with the Windsor Versamatic vacuum cleaner 2 passes at 1/2ft/sec. |
MilliCare Textile and Carpet Care
LaGrange, GA
888-886-2273
Visit Website
|
|
Nobles Strive Compact – Ready Space
Vacuum using a Nobles UltraGlide 12” SMV vacuum (2 front back – total 4 passes) at 1.8 ft/sec. Pre-Spray carpet to be cleaned with ReadySpace Pre-treatment 8oz/1gl at 1 gl/400 sq ft. The treated sample Is allowed to dwell for 10 minutes. Then hot water extract Using Strive Compact carpet extractor using 1 wet extraction at a Rate of 100 ft/per minute on each pass. |
Nobles Industries (Tennant Co.)
Holland, MI
800-510-0616
Visit Website
|
|
Nobles Strive Rider System
Each sample is cleaned using the Nobles Strive Rider cleaning process. The first step is to vacuum 4 passes at 1.8ft/sec with the Tennant 3120 Dual Motor vacuum. The next step is to pre-spray with Nobles ReadySpace pre-Treatment 8oz/1gl at 1gl/500ft2. The treated sample is allowed to dwell for 10 minutes prior to cleaning. The following step is to hot water extract the samples with Nobles Strive Rider using 1 wet extraction pass at a rate of 50ft/min on each pass. |
Nobles Industries (Tennant Co.)
Holland, MI
800-510-0616
Visit Website
|
|
Nobles Strive – Ready Space
Vacuum using a Nobles TV1200 12” vacuum (2 front back – total 4 passes) at 1.8 ft/sec. Pre-Spray carpet to be cleaned with ReadySpace Pre-treatment 8oz/1gl at 1 gl/400 sq ft. The treated sample Is allowed to dwell for 10 minutes. Then hot water extract
Using Strive carpet extractor using 1 wet extraction at a Rate of 100 ft/per minute on each pass. |
Nobles Industries (Tennant Co.)
Holland, MI
800-510-0616
Visit Website
|
|
Oxi Fresh Franchising Company, Inc.
Pre-vacuum using a CRI Gold Level vacuum 4 passes at 1.8 feet/second. Prespray with 6 scoops OxiPrespray with Enzymes per gallon of water. Apply at 1 gallon/1000 sq ft and allow 20 minutes dwell time. Spray with 1 scoop OxiPowder + 8 oz Encapsulator per gallon of water. Apply at 1 gallon/1000 sq ft. Apply OxiSponge 1 pound/100 sq ft Agitate with OF1000 Machine with dust covers attached using soft brushes 2 passes at 1.8 feet/second. Attach renovators and agitate 2 passes at 1.8 feet/second. Allow 60 minutes dwell time. Post vacuum using a CRI Gold Level vacuum 2 passes at 0.5 feet/second. |
Oxi Fresh Franchising Company, Inc.
Lakewood, CO
1-877-OXIFRESH
Visit Website
|
|
Host AV1-A Dry Carpet Cleaning System, Host Dry Carpet Cleaner
First step is to pre-vacuum with a CRI Green Label vacuum cleaner 4 strokes (4passes - 1 forward, 1 backward, 1 forward, 1 backward) at 1.8ft/sec. The next step is to apply the Host Dry Carpet Cleaner at 1 lb/32ft2, followed by agitation using the Host Retail AV1A carpet machine 2 passes north south at 1.8 ft/sec on each pass. Allow the product to dwell for 30 minutes. The final step is to post vacuum with the CRI Green Label vacuum cleaner 2 passes at 0.5 ft/sec on each pass. |
Racine Industries, Inc.
Racine, WI
800-558-9439
Visit Website
|
|
Reliant Dry Carpet Cleaning System, Host Dry Carpet Cleaner
First step is to pre-vacuum with a CRI Green Label vacuum cleaner 4 strokes (4passes - 1 forward, 1 backward, 1 forward, 1 backward) at 1.8ft/sec. The next step is to apply the Host Dry Carpet Cleaner at 1 lb/32ft2, followed by agitation using the Reliant Dry Cleaning carpet machine 2 passes north south at 1.8 ft/sec on each pass. Allow the product to dwell for 30 minutes. The final step is to post vacuum with the CRI Green Label vacuum cleaner 2 passes at 0.5 ft/sec on each pass. |
Racine Industries, Inc.
Racine, WI
800-558-9439
Visit Website
|
|
|
Tennant R14 System
Each sample is cleaned using the Tennant R14 cleaning process. The first step is to vacuum 4 passes at 1.8ft/sec with the Tennant 3120 Dual Motor vacuum. The next step is to pre-spray with Tennant ReadySpace pre-Treatment 8oz/1gl at 1gl/500ft2. The treated sample is allowed to dwell for 10 minutes prior to cleaning. The following step is to hot water extract the samples with Tennant R14 using 1 wet extraction pass at a rate of 50ft/min on each pass. |
Tennant Co.
Minneapolis, MN
800-553-8033
Visit Website
|
|
Tennant R1610 – Ready Space
Vacuum using a Tennant 3200 12” vacuum (2 front back – total 4 passes) at 1.8 ft/sec. Pre-Spray carpet to be cleaned with Tennant ReadySpace Pre-treatment 8oz/1gl at 1 gl/400 sq ft. The treated sample Is allowed to dwell for 10 minutes. Then hot water extract Using 1610 carpet extractor using 1 wet extraction at a Rate of 100 ft/per minute on each pass. |
Tennant Co.
Minneapolis, MN
800-553-8033
Visit Website
|
|
Tennant R3 – Ready Space
Vacuum using a Tennant 3110 12” Single motor vacuum (2 front back – total 4 passes) at 1.8 ft/sec. Pre-Spray carpet to be cleaned with Tennant ReadySpace Pre-treatment 8oz/1gl at 1 gl/400 sq ft. The treated sample Is allowed to dwell for 10 minutes. Then hot water extract Using R3 carpet extractor using 2 wet extraction passes at a Rate of 100 ft/per minute on each pass. |
Tennant Co.
Minneapolis, MN
800-553-8033
Visit Website
|
|
iCapsol, Mini, IMX
The first step is to pre-vacuum with the Windsor Versamatic vacuum cleaner – four passes at 1.8ft/sec. The second step is to pre-spray with ProChem Procap diluted to 8 oz. per gallon of water (do not over wet). The third step – do not allow chemical to dry, agitate with the Windsor iCapsol Mini machine 4 passes at 1.8 ft/sec. The fourth step is to vacuum after a 40 minutes minimum drying time with the Windsor Versamatic vacuum cleaner 4 passes at ½ ft/sec. |
Windsor
Englewood, CO
800-444-7654
Visit Website
|
|
XL North Grab Carpet Care Systems
Use the XL Brands 5 step cleaning process. The first step is to pre-vacuum 4 passes at 1.8ft/sec. The second step is to pre-spray the carpet with XL Grab Carpet Pre-Spray at 1.0gl/200ft². The third step is broadcast Grab Dry at 2.2lb/130ft² onto the carpet. The fourth step is agitate the carpet with the XLerator machine using the white brushes 4 passes at 1.8ft/sec. The treated carpet is allowed to dwell for 60 minutes. The final step is vacuum the carpet 2 passes at 0.5ft/sec. |
XL North
Fall River, MA
888-530-2259
Visit Website
|
